Gas Equipment

Showing 1–12 of 95 results

  • G00017

    ARGON / CO2 FLOW METER

    Code: G00017
    A preset regulator or flow meter is suitable for controlling an accurate gas flow from your Argon / CO2 gas cylinder to your torch. Commonly used in the MIG & TIG Welding processes.

    This model has a separate gauge indicating bottle content as well as a tube indicating outlet flow control in gas per liter. In ideal indoor workshop conditions a rough indication is to set the regulator to 5L/min for TIG welding and 15L/min for MIG welding. These indicators are not set in stone but are rather tips to keep your gas usage to a minimum with maximum results. There are many factors to influence the amount of gas needed so use those measurements to start off with and adjust until optimum weld pool protection is ascertained.


    Read More
  • W00046

    BEETLE STRAIGHT LINE CUTTER

    Code: W00046
    A high quality motor driven flame cutting machine designed to cut straight lines, circles as well as bevels with clean, sharp, smooth edges.
    For use with ANME cutting nozzles all functions are controlled for forward, reverse and off positions with a clutch lever & speed adjustment knob.
    Straight line cutting is ensured by an unlimited amount of interlocking track ranging between 1800mm to 2000mm long (Hose length allowing).
    An adjustable Radius bar is available for circle cutting and circle cutting track are available separately on request. Depending on the Quality of the cutting nozzles used, high speed cutting of around 240mm to 2400mm/min can be achieved as well as 30mm to 300mm/min can be achieved at around about a 60% duty cycle.
    Machine Specs
    *Cutting Speed: 80 – 800mm/min (Average)
    *Traveling Speed (High) – 240 -2400mm/min
    *Speed Control: Stepless
    *Speed Meter: Dial induction/ with conversion scale
    *Power Input: 220V
    *Machine Dimensions: LxBxH 430mm x 170mm x 215mm
    *Maximum Load Weight: 50 Kg
    *Weight: 10 Kg


    Read More
  • G00066

    BULL NOSE STEM – LONG

    Code: G00066
    A stem forged from brass to make an outlet channel for the gas cylinder through a stem that connects to the regulator. The thickness and thread is produced per specification for each individual regulator. The inlet stem is a certain length, depending on the gas used and has a bull nose at one end which fits into the cylinder outlet and is tightened with a bull nose nut of the same thread. The stem also has a metal mesh gauze at the one end to assist in the prevention of any unwanted material from entering the regulator. The other end is has a die cut thread that would correspond to the particular gas it is being used for.

    These Bull Nose Stems are available in a variety of sizes & lengths.


    Read More
  • G00008

    CUTTING ATTACHMENT ( HEAVY DUTY)

    Code: G00008
    *Forged Brass Head with Stainless Steel tubes
    *For Use with Acetylene and LPG
    *Cuts up to 75mm Steel
    *Nozzle mixing of gasses ensures maximum safety
    *Can be used with ANM & PNM Cutting Nozzles
    *90 Deg Head
    *Attaches directly onto Type 2 shank.


    Read More
  • G00008AG00008A

    CUTTING ATTACHMENT ( PORTAPAK TYPE )

    Code: G00008A
    *Forged Brass Head with Stainless Steel tubes for medium duty work
    *For Use with AFN-N Nozzles for cutting steel up to 35mm thick
    *90 Deg Head
    *Attaches directly onto Type 2 medium duty shank.
    *Can be used for cutting and welding of material up to 4mm thick simply by changing the appropriate nozzles.


    Read More
  • G00030---G00035

    CUTTING NOZZLE ANM 1/16 ( 12 – 75 mm )

    Code: G00032
    A Nozzle that utilizes the nozzle pre-mix principal whereby the fuel gas and oxygen are kept separate right up until the preheated orifices of the nozzle.
    This system keep the volume of mixed gasses to an absolute minimum and therefore reduces the magnitude of a backfire.
    Nozzles are made from copper for good heat dissipation and should be cleaned with appropriate cleaning nozzles and dressed back, the flame shape and nozzle depend heavily on orifices having sharp square edges.
    Beware of cheap imports that are bell shaped and use only approved nozzle cleaners.
    Specifications
    *50-75mm Material cutting thickness
    *Oxygen Pressure: 350 KPA
    *180 – 300mm/min

    Paying half the price isn’t worth paying with your life.


    Read More
  • G00030---G00035

    CUTTING NOZZLE ANM 1/32 ( 3 – 6 mm )

    Code: G00030
    A Nozzle that utilizes the nozzle pre-mix principal whereby the fuel gas and oxygen are kept separate right up until the preheated orifices of the nozzle.
    This system keep the volume of mixed gasses to an absolute minimum and therefore reduces the magnitude of a backfire.
    Nozzles are made from copper for good heat dissipation and should be cleaned with appropriate cleaning nozzles and dressed back, the flame shape and nozzle depend heavily on orifices having sharp square edges.
    Beware of cheap imports that are bell shaped and use only approved nozzle cleaners.
    Specifications
    *3 – 6mm Material cutting thickness
    *Oxygen Pressure: 150 KPA
    *500 – 850mm/min

    Paying half the price isn’t worth paying with your life.


    Read More
  • G00030---G00035

    CUTTING NOZZLE ANM 1/8 ( 150 – 300 mm )

    Code: G00035
    A Nozzle that utilizes the nozzle pre-mix principal whereby the fuel gas and oxygen are kept separate right up until the preheated orifices of the nozzle.
    This system keep the volume of mixed gasses to an absolute minimum and therefore reduces the magnitude of a backfire.
    Nozzles are made from copper for good heat dissipation and should be cleaned with appropriate cleaning nozzles and dressed back, the flame shape and nozzle depend heavily on orifices having sharp square edges.
    Beware of cheap imports that are bell shaped and use only approved nozzle cleaners.
    Specifications
    *250-300mm Material cutting thickness
    *Oxygen Pressure: 550 KPA
    *90 – 125mm/min

    Paying half the price isn’t worth paying with your life.


    Read More
  • G00030---G00035

    CUTTING NOZZLE ANM 3/32 ( 100 – 150 mm )

    Code: G00034
    A Nozzle that utilizes the nozzle pre-mix principal whereby the fuel gas and oxygen are kept separate right up until the preheated orifices of the nozzle.
    This system keep the volume of mixed gasses to an absolute minimum and therefore reduces the magnitude of a backfire.
    Nozzles are made from copper for good heat dissipation and should be cleaned with appropriate cleaning nozzles and dressed back, the flame shape and nozzle depend heavily on orifices having sharp square edges.
    Beware of cheap imports that are bell shaped and use only approved nozzle cleaners.
    Specifications
    *100-150mm Material cutting thickness
    *Oxygen Pressure: 300 KPA
    *150 – 180mm/min

    Paying half the price isn’t worth paying with your life.


    Read More
  • G00030---G00035

    CUTTING NOZZLE ANM 3/64 ( 6 – 12 mm )

    Code: G00031
    A Nozzle that utilizes the nozzle pre-mix principal whereby the fuel gas and oxygen are kept separate right up until the preheated orifices of the nozzle.
    This system keep the volume of mixed gasses to an absolute minimum and therefore reduces the magnitude of a backfire.
    Nozzles are made from copper for good heat dissipation and should be cleaned with appropriate cleaning nozzles and dressed back, the flame shape and nozzle depend heavily on orifices having sharp square edges.
    Beware of cheap imports that are bell shaped and use only approved nozzle cleaners.
    Specifications
    *6-12mm Material cutting thickness
    *Oxygen Pressure: 200 KPA
    *440 – 700mm/min

    Paying half the price isn’t worth paying with your life.


    Read More
  • G00030---G00035

    CUTTING NOZZLE ANM 5/64 ( 75 – 100 mm )

    Code: G00033
    A Nozzle that utilizes the nozzle pre-mix principal whereby the fuel gas and oxygen are kept separate right up until the preheated orifices of the nozzle.
    This system keep the volume of mixed gasses to an absolute minimum and therefore reduces the magnitude of a backfire.
    Nozzles are made from copper for good heat dissipation and should be cleaned with appropriate cleaning nozzles and dressed back, the flame shape and nozzle depend heavily on orifices having sharp square edges.
    Beware of cheap imports that are bell shaped and use only approved nozzle cleaners.
    Specifications
    *75-100mm Material cutting thickness
    *Oxygen Pressure: 300 KPA
    *180 – 250mm/min

    Paying half the price isn’t worth paying with your life.


    Read More
  • G00053---G00058

    CUTTING NOZZLE HARRIS STYLE (OXY / ACE) 0F

    Code: G00055
    A Harris Styled screw in type nozzle that is compatible with genuine or copy Harris Monarch 28 cutting torches. Use for oxygen / acetylene cutting.
    Specifications
    *3-6mm Material cutting thickness
    *Acetylene
    Paying half the price isn’t worth paying with your life.
    We would always recommend a genuine Harris cutting nozzle instead of a copy, life expectancy of the nozzle cannot be compared to a genuine Harris products and personal safety is not guaranteed when using these Nozzle’s. By purchasing this copy nozzle, you indemnify E-Weld Online (Pty) Ltd and any of its employee’s, contractors as well as sub contractors for any damage to equipment, lifespan of nozzle and may have no claim whatsoever regarding the use of this imported copy which includes serious injury or loss of life. Use at your own peril.

    Check on the Harris Gas Equipment page for the genuine Nozzle and/or torch. All genuine Harris products are 100% tested 100% of the time.


    Read More

Showing 1–12 of 95 results